GB/T1043.1-2008 Determination of impact properties of plastic simple beam - Part 1: Non-instrumental impact test scheme
This scheme applies to the following range of materials:
Hard thermoplastic molding and extrusion materials, including filler materials and reinforced unfilled materials, rigid thermoplastic sheet;
Hard thermosetting molding materials, including filled and reinforced materials, hard thermosetting sheets, including laminates;
Fiber-reinforced thermosetting and thermoplastic composites, including unidirectional or non-unidirectional reinforcements such as felts, fabrics, textile rovings, staple tow, composite and hybrid composites, glass rovings and broken fibers, and prepreg materials Sheet (prepreg);
Thermotropic liquid crystal polymer.
This solution is generally not suitable for hard porous materials and sandwich materials containing porous materials. In addition, long fiber reinforced composites or thermotropic liquid crystal polymers generally do not use notched specimens.
This program is mainly applied to the plastic products enterprises to carry out plastic incoming materials and product quality inspections. The plan includes the objectives of impact tests, relevant test standards, sample types, and typical test equipment for application and test applications.
1, the impact of the test target
The plastic was tested under the specified conditions for the impact strength of the simply supported beam and the basic impact mechanical properties of the plastic material were examined.
The characteristic parameters are:
Unnotched Specimen Simply Supported Beam Impact Strength: The impact energy absorbed when an unnotched specimen is broken. It is related to the original cross-sectional area of ​​the specimen and is expressed in KJ/m2.
Notched Specimen Simply Supported Beam Impact Strength: The impact energy absorbed when a notched specimen breaks is related to the original cross-sectional area at the specimen notch and is expressed in KJ/m2.
2. Related test standards:
GB/T1043.1-2008 Determination of impact properties of plastic simple beam - Part 1: Non-instrumental impact test
GB/T2918-1998 Standard Environment for Conditioning and Testing of Plastic Specimen
GB/T3360-1982 Statistical Processing and Interpretation of Mean Estimates and Confidence Intervals
GB/T 4550-2005 Preparation of unidirectional fiber reinforced plastic plates for testing
GB/T 5471-2008 Plastic thermosetting plastic specimens
GB/T9352-2008 Plastic Thermoplastic Material Specimen Compression Molding
GB/T 11997-2008 Plastics Multipurpose Samples
GB/T 17037.1-1997 Preparation of injection molded specimens of thermoplastics - Part 1: General principles and preparation of multipurpose specimens and strips
GB/T 17037.3-2003 Preparation of injection molded specimens of plastics thermoplastic materials Part 3: Small square test pieces
GB/T21189-2007 Inspection of Pendulum Impact Testing Machines for Plastic Simple Beams, Cantilever Beams and Tensile Impact Tests
ISO 2818-1994 Plastics - Machined preparation of test specimens
BS ISO 10724-1-1998 Plastics - Injection moulding of thermosetting powder moulded composite specimens - Part 1: General principles and moulding of multipurpose specimens
3, sample type: rectangular with a gap and without a gap
4. Typical test equipment for test applications:
4.1 Test Equipment
Test Equipment Standard Configuration: Host + Accessories
The mainframe is equipped with simple-beam pendulums with different impact energy to meet the material testing requirements for different impact strengths.
Host: PTM7000 Series Feilong Plastic Pendulum Impact Tester
PTM7000 Series
The structure of the main frame is novel and simple, and the hanging part adopts the simple beam structure, which makes the structure of the pendulum part more reasonable, improves the stress of the pendulum shaft, reduces the frictional resistance caused by the bearing, and has simple and reliable structure, high processing precision, and low energy loss.
PTM7000 Series LCD Display
Energy display using LMC LCD screen, no need to read data from the dial, no data error, high accuracy and high efficiency.
PTM7000 Series Hanging Pendulum Device
Newly designed hanging-off device, manual hanging pendulum, simple and reliable. The pendulum is driven by an electromagnet, making the impact operation simple and convenient.
annex:
Simple beam options: 1J, 2J, 4J 7.5J, 15J, 25J, 50J
Simple beam swing
The pendulum uses a three-dimensional software design to ensure accurate impact constants. Pendulum body chrome plating, coordinated with the host
4.2 Sample Preparation Instrument: Injection Molding Machine or Machine Preparation, Notch QTM1000 Notch Sample Preparation System
QTM1000 Notch Sampler
Sample picture
Car Charger Adapter,Usb C Car Charger,Car Phone Charger,Mini Usb Charger, USB Socket
Dongguan Andu Electronic Co., Ltd. , https://www.autoido.com