A, LED LAMP use precautions
1. Welding conditions : (the solder joint needs to be 2mm or more from the root of the resin)
◆Dip soldering: Please finish soldering once at 260 ° C for 5 seconds while avoiding resin immersion in the tin bath.
◆ Soldering iron: Use a 30W soldering iron with a tip temperature not higher than 350 °C and soldering once within 5 seconds.
Do not apply external force to the product while welding. Take care to avoid corrosion or discoloration of the LED pins, otherwise it will cause soldering difficulties. It is recommended to use them as soon as possible.
2, the use of attention:
â—†The lead forming must be completed before soldering. The distance between the mounting holes on the circuit board should be the same as the electrode pins.
â—†The product will be defective when the product is cut at high temperature. Please cut the pin at normal temperature.
â—†Before the soldering temperature returns to normal, the LED must be protected from any vibration or external force.
3, static protection
High-brightness blue, green and white products are sensitive to static electricity. In use, it is necessary to pay attention to static electricity surges that will damage or destroy the product. The workbench that is in contact with the product should be grounded through a resistor with a conductive pad; the tip of the soldering iron must be Grounding is recommended; an ionizer is recommended.
4, cleaning
Special care must be taken when cleaning the gel with chemicals, as some chemicals damage the surface of the gel and cause fading such as trichloroethylene, acetone, and the like. It can be wiped and immersed in ethanol for less than 3 minutes at room temperature.
B, CHIP LED use precautions
1. Welding conditions:
◆Reflow soldering: Preheat at 150 ° C for 2 minutes, and heat once at 240 ° C for 5 s.
◆ Soldering iron soldering: Use a temperature-controlled soldering iron with a maximum temperature of 25W. The tip temperature is not higher than 320 °C, and welding is completed once within 3 seconds.
Do not apply external force to the product while welding. Do not bend the circuit board after soldering.
2, packaging:
â—†Because the moisture absorption of the resin causes evaporation and swelling of the water during welding, the interface may be peeled off, so the purpose of the moisture-proof packaging is to ensure the lowest moisture in the package.
◆The product should be used within one year from the date of packaging. Before the package is unopened, it should be stored in an environment with a temperature of 5 to 30 ° C and a relative humidity of <60%.
◆ After unpacking the package, the product must be welded and used within 24 hours. Otherwise, the product must be stored in an environment with a temperature of 5 to 30 ° C and a relative humidity of < 30% for a period of less than one week. If there is a product that is not used, please put it. Back to moisture bag seal storage ◆ If the product exceeds the above storage requirements or is damp, it must be baked at 60 ± 5 ° C for 12 hours.
â—†The surface of the product electrode is gold-plated, which is easy to be damaged by corrosion or discoloration. It is recommended to use it as soon as possible.
â—† Take care to avoid rapid changes in ambient temperature, especially in humid environments.
3, static protection
High-brightness blue, green and white products are sensitive to static electricity. In use, it is necessary to pay attention to static electricity surges that will damage or destroy the product. The workbench that is in contact with the product should be grounded through a resistor with a conductive pad; the tip of the soldering iron must be Grounding is recommended; an ionizer is recommended.
Smart Led Control Box allows multiple sensors to control all online LED Lights independently. The Led Controller Box is a part ot Led Wiring Control System. It`s have 3 ports for optional sensors IR/PIR/TOUCH/PUSH. 6 ports connect LED cabinet lights and one ports connect Super Thin LED Driver. Dimming and memory functions available. One control box can connect another box. Very easy to control LED Under Cabinet Light .
Description of Smart LED Control Box
Item: Smart LED control boc
Size: 80*40*14mm
Voltage:12V/24V
Max Power: 30W/12V 60W/24V
Input: DC12V/24V
Output: DC12V/24V
Certifications:CE
Warranty:3 years
MOQ: 500pcs
FAQ:
Q1. Can I have a sample order for led light?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A:Sample needs 3-5 days, mass production time needs 1-2 weeks for order quantity more than 1000pcs
Q3. Do you have any MOQ limit for led light order?
A: Low MOQ, 1pc for sample checking is available
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.
Smart LED Control Box
Smart Led Control Box,Led Controller Box,Led Smart Controller Box,Plastic Led Smart Control Box
Shenzhen Jedver Smart Lighting Co., Ltd. , http://www.jederwell.com